Installation:
Installation on a whole with the TJ05 case is made quite simple, as Silverstone has made basically everything toolless. I'll walk you through my entire installation process to show how all the toolless parts work, as well as give some hints and tips for installation in the TJ05 case.

The first items I chose to install were the hard drive and CD drives in their appropriate places. The rails for hard drives/floppy drives are in the accessory kit which is found in the bottom of the case and the CD drive rails are in the box which was found sitting in the bottom of the case. For both the CD and hard drive, the rails need to be simply held in the screw holes while you slide the drives in, and once it is all the way in it will click into place. That's it, no need to screw these rails to the drives first - VERY nice feature!

The next step I performed was to install the motherboard. Unfortunately this is a process which still requires some good old screws and motherboard standoffs. The standoffs are screwed into the appropriate holes on the motherboard tray that line up with the mounting holes in the motherboard. Remember not to mount all the standoffs, just the ones you require for your particular motherboard. There was a small problem that I encountered here. Near my PCI Express video slot there are two holes on my motherboard which are roughly 2 inches apart, however, the case only had a standoff hole for one of these. Unfortunately I have a standoff missing there and pushing cards in and out of that slot just needs to be done carefully so as to not flex the circuit board too much. That was the only minor problem I encountered with installing the motherboard, everything else went very smooth.

After the motherboard was installed it was time to install my video card, which in this case is an XFX GeForce 6600GT PCI-E. All the slots on the rear of this case are toolless and there is a small clip which must be slid back, the card installed, then slid forward again to hold the card firmly in place. This is where another small problem snuck up for me. The metal bracket of the video card which goes against the back slot and wraps around where the clip should push up against, didn't want to fit in the area allotted for it on the toolless unit on the back. Unfortunately after trying many different approaches to this problem, I ended up just removing the toolless bracket from the slots and using a screw to secure the video card. Not a big deal at all. Being as the toolless bracket is all one piece I couldn't remove just the one on the video slot, so I removed the entire bracket in my case.

The last major step of installation is the power supply. In the TJ05 the PSU must go in through the rear of the case. This is done by removing a rectangular bracket which mounts onto the power supply, then everything gets slid back into the case, and the bracket screwed back onto the rear of the case again.

The last step is to wire up the entire system and do any cosmetic extras like hiding, looming or zip tieing all the wires out of sight. The extra length in the case provided more room than normal between the motherboard and the rear of the drive bays. This makes wiring and working inside the case a joy. The window leaves a little area at the front of the case that is not visible from the outside and I found this area a nice place to tuck some extra wires out of sight. As well, the brace that goes across the entire case that the PSU rests on is big enough that a cathode light fits just perfectly behind it and is not visible from the outside.

Below I've included an image of my PC entirely installed in the case. For those who chose not to mount fan(s)/hard drive(s) in the small steel door on the inside, you may chose to remove it and allow the full unobstructed view of everything inside the case.

(Click to enlarge)

(Note: Hard drive is in a silencing box so I removed the drive cage that came with the case, one clip to easily take it out)

Testing:
To test cases I look at the overall usability, build quality and noise performance.
In terms of usability, the TJ05 passes 100%, with the majority of the case being toolless, installation of any new hardware goes very quick and easy.
The build quality of the case is also excellent overall. The paint job is perfect and has no imperfections that I could find at all. As well, since the case is manufactured mainly of steel and aluminum I found everything to be very sturdy during assembly. Nothing is "flimsy" such as the side panels or any of the brackets or plates.
With the TJ05 being cooled by the two included 120mm fans, I was very impressed with how quiet they are. I have used 120mm fans in the past which were fairly loud and annoying, but the Silverstone fans in this case are by far some of the quietest 120mm fans I've used, at around 21dB.

<<Previous Page<< - >>Next Page>>